Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-RELEASE #0: Thu Jan  1 14:37:25 UTC 2009
    root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0dec000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0dec1b0.
Calibrating clock(s) ... i8254 clock: 1193165 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2100209104 Hz
CPU: AMD Phenom(tm) 8450e Triple-Core Processor (2100.21-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x100f23  Stepping = 3
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x802009<SSE3,MON,CX16,POPCNT>
  AMD Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
  AMD Features2=0x7ff<LAHF,CMP,SVM,ExtAPIC,CR8,<b5>,<b6>,<b7>,Prefetch,<b9>,<b10>>
  Cores per package: 3
Data TLB: 48 entries, fully associative
Instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 128 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory  = 3489333248 (3327 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001025000 - 0x00000000cc4d6fff, 3410698240 bytes (832690 pages)
avail memory = 3410042880 (3252 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x31
pnpbios: Found PnP BIOS data at 0xc00f5010
pnpbios: Entry = f0000:678a  Rev = 1.0
Other BIOS signatures found:
ULE: setup cpu group 0
ULE: setup cpu 0
ULE: adding cpu 0 to group 0: cpus 1 mask 0x1
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
wlan_amrr: <AMRR Transmit Rate Control Algorithm>
wlan: <802.11 Link Layer>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (Jan  1 2009 14:37:00)
ACPI: RSDP @ 0x0xfa560/0x0014 (v  0 ACPIAM)
ACPI: RSDT @ 0x0xcffb0000/0x003C (v  1 011309 RSDT1651 0x20090113 MSFT 0x00000097)
ACPI: FACP @ 0x0xcffb0200/0x0084 (v  1 011309 FACP1651 0x20090113 MSFT 0x00000097)
ACPI Warning (tbfadt-0505): Optional field "Pm2ControlBlock" has zero address or length:        0       0/1 [20070320]
ACPI: DSDT @ 0x0xcffb0490/0x9D66 (v  1  A78CM A78CM113 0x00000000 INTL 0x20051117)
ACPI: FACS @ 0x0xcffbe000/0x0040
ACPI: APIC @ 0x0xcffb0390/0x006C (v  1 011309 APIC1651 0x20090113 MSFT 0x00000097)
ACPI: MCFG @ 0x0xcffb0400/0x003C (v  1 011309 OEMMCFG  0x20090113 MSFT 0x00000097)
ACPI: OEMB @ 0x0xcffbe040/0x0072 (v  1 011309 OEMB1651 0x20090113 MSFT 0x00000097)
ACPI: HPET @ 0x0xcffba200/0x0038 (v  1 011309 OEMHPET  0x20090113 MSFT 0x00000097)
ACPI: SSDT @ 0x0xcffba240/0x03FC (v  1 A M I  POWERNOW 0x00000001 AMD  0x00000001)
npx0: INT 16 interface
acpi0: <011309 RSDT1651> on motherboard
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xda723000 pa 0x1000
atpic: Programming IRQ9 as level/low
pci_open(1):	mode 1 addr port (0x0cf8) is 0x8000a340
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=96001022)
pcibios: BIOS version 3.00
AcpiOsDerivePciId: \\_SB_.PCI0.RS78.NB2_ -> bus 0 dev 0 func 0
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
AcpiOsDerivePciId: \\_SB_.PCI0.SATA.SACS -> bus 0 dev 17 func 0
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of ffb80000, 80000 (3) failed
acpi0: reservation of fec10000, 20 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cff00000 (3) failed
ACPI HPET table warning: Sequence is non-zero (2)
ACPI timer: 0/16 0/11 0/14 0/17 0/10 0/11 0/12 0/12 0/16 0/12 -> 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  4 7 10 11 12 14 15
  Validation          0   10   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  4 7 10 11 12 14 15
  Validation          0   10   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    7   N     0  4 7 10 11 12 14 15
  Validation          0    7   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  4 7 10 11 12 14 15
  Validation          0   11   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  4 7 10 11 12 14 15
  Validation          0  255   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  4 7 10 11 12 14 15
  Validation          0  255   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    4   N     0  4 10 11 12 14 15
  Validation          0    4   N     0  4 10 11 12 14 15
  After Disable       0  255   N     0  4 10 11 12 14 15
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  4 7 10 11 12 14 15
  Validation          0  255   N     0  4 7 10 11 12 14 15
  After Disable       0  255   N     0  4 7 10 11 12 14 15
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: vend: 0x4353 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.4.INTA at func 0: 10
ACPI: Found matching pin for 0.7.INTA at func 0: 11
ACPI: Found matching pin for 0.20.INTA at func 1: 255
ACPI: Found matching pin for 0.20.INTA at func 2: 10
ACPI: Found matching pin for 0.20.INTC at func 5: 7
ACPI: Found matching pin for 0.18.INTA at func 0: 10
ACPI: Found matching pin for 0.18.INTB at func 2: 10
ACPI: Found matching pin for 0.19.INTA at func 0: 7
ACPI: Found matching pin for 0.19.INTB at func 2: 11
ACPI: Found matching pin for 0.17.INTA at func 0: 4
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found->	vendor=0x1022, dev=0x9600, revid=0x00
	domain=0, bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x9602, revid=0x00
	domain=0, bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x1a (6500 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x9604, revid=0x00
	domain=0, bus=0, slot=4, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
pcib0: matched entry for 0.4.INTA (src \\_SB_.LNKA:0)
pcib0: slot 4 INTA routed to irq 10 via \\_SB_.LNKA
found->	vendor=0x1022, dev=0x9607, revid=0x00
	domain=0, bus=0, slot=7, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
pcib0: matched entry for 0.7.INTA (src \\_SB_.LNKD:0)
pcib0: slot 7 INTA routed to irq 11 via \\_SB_.LNKD
found->	vendor=0x1002, dev=0x4390, revid=0x00
	domain=0, bus=0, slot=17, func=0
	class=01-01-8f, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0230, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=4
	powerspec 2  supports D0 D3  current D0
	map[10]: type I/O Port, range 32, base 0xb000, size  3, enabled
	map[14]: type I/O Port, range 32, base 0xa000, size  2, enabled
	map[18]: type I/O Port, range 32, base 0x9000, size  3, enabled
	map[1c]: type I/O Port, range 32, base 0x8000, size  2, enabled
	map[20]: type I/O Port, range 32, base 0x7000, size  4, enabled
	map[24]: type Memory, range 32, base 0xfe7ff800, size 10, enabled
pcib0: matched entry for 0.17.INTA (src \\_SB_.LNKG:0)
pcib0: slot 17 INTA routed to irq 4 via \\_SB_.LNKG
found->	vendor=0x1002, dev=0x4397, revid=0x00
	domain=0, bus=0, slot=18, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0102, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	map[10]: type Memory, range 32, base 0xfe7fe000, size 12, enabled
pcib0: matched entry for 0.18.INTA (src \\_SB_.LNKA:0)
pcib0: slot 18 INTA routed to irq 10 via \\_SB_.LNKA
found->	vendor=0x1002, dev=0x4398, revid=0x00
	domain=0, bus=0, slot=18, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	map[10]: type Memory, range 32, base 0xfe7fd000, size 12, enabled
pcib0: matched entry for 0.18.INTA (src \\_SB_.LNKA:0)
pcib0: slot 18 INTA routed to irq 10 via \\_SB_.LNKA
found->	vendor=0x1002, dev=0x4396, revid=0x00
	domain=0, bus=0, slot=18, func=2
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0102, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xfe7ff000, size  8, enabled
pcib0: matched entry for 0.18.INTB (src \\_SB_.LNKB:0)
pcib0: slot 18 INTB routed to irq 10 via \\_SB_.LNKB
found->	vendor=0x1002, dev=0x4397, revid=0x00
	domain=0, bus=0, slot=19, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0102, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=7
	map[10]: type Memory, range 32, base 0xfe7fc000, size 12, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.LNKC:0)
pcib0: slot 19 INTA routed to irq 7 via \\_SB_.LNKC
found->	vendor=0x1002, dev=0x4398, revid=0x00
	domain=0, bus=0, slot=19, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=7
	map[10]: type Memory, range 32, base 0xfe7fb000, size 12, enabled
pcib0: matched entry for 0.19.INTA (src \\_SB_.LNKC:0)
pcib0: slot 19 INTA routed to irq 7 via \\_SB_.LNKC
found->	vendor=0x1002, dev=0x4396, revid=0x00
	domain=0, bus=0, slot=19, func=2
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0102, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xfe7fa800, size  8, enabled
pcib0: matched entry for 0.19.INTB (src \\_SB_.LNKD:0)
pcib0: slot 19 INTB routed to irq 11 via \\_SB_.LNKD
found->	vendor=0x1002, dev=0x4385, revid=0x3a
	domain=0, bus=0, slot=20, func=0
	class=0c-05-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0403, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x439c, revid=0x00
	domain=0, bus=0, slot=20, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	MSI supports 2 messages
	map[20]: type I/O Port, range 32, base 0xff00, size  4, enabled
found->	vendor=0x1002, dev=0x4383, revid=0x00
	domain=0, bus=0, slot=20, func=2
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D3  current D0
	map[10]: type Memory, range 64, base 0xfe7f4000, size 14, enabled
pcib0: matched entry for 0.20.INTA (src \\_SB_.LNKA:0)
pcib0: slot 20 INTA routed to irq 10 via \\_SB_.LNKA
found->	vendor=0x1002, dev=0x439d, revid=0x00
	domain=0, bus=0, slot=20, func=3
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x4384, revid=0x00
	domain=0, bus=0, slot=20, func=4
	class=06-04-01, hdrtype=0x01, mfdev=1
	cmdreg=0x0105, statreg=0x02a0, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x4399, revid=0x00
	domain=0, bus=0, slot=20, func=5
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0102, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=7
	map[10]: type Memory, range 32, base 0xfe7f9000, size 12, enabled
pcib0: matched entry for 0.20.INTC (src \\_SB_.LNKC:0)
pcib0: slot 20 INTC routed to irq 7 via \\_SB_.LNKC
found->	vendor=0x1022, dev=0x1200, revid=0x00
	domain=0, bus=0, slot=24, func=0
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1201, revid=0x00
	domain=0, bus=0, slot=24, func=1
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1202, revid=0x00
	domain=0, bus=0, slot=24, func=2
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1203, revid=0x00
	domain=0, bus=0, slot=24, func=3
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1204, revid=0x00
	domain=0, bus=0, slot=24, func=4
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xc000-0xcfff
pcib1:   memory decode     0xfe800000-0xfe9fffff
pcib1:   prefetched decode 0xd0000000-0xdfffffff
ACPI: Found matching pin for 1.5.INTA at func 0: 7
ACPI: Found matching pin for 1.5.INTB at func 1: 11
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found->	vendor=0x1002, dev=0x9614, revid=0x00
	domain=0, bus=1, slot=5, func=0
	class=03-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0107, statreg=0x4010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=7
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Prefetchable Memory, range 32, base 0xd0000000, size 28, enabled
pcib1: requested memory range 0xd0000000-0xdfffffff: good
	map[14]: type I/O Port, range 32, base 0xc000, size  8, enabled
pcib1: requested I/O range 0xc000-0xc0ff: in range
	map[18]: type Memory, range 32, base 0xfe9f0000, size 16, enabled
pcib1: requested memory range 0xfe9f0000-0xfe9fffff: good
	map[24]: type Memory, range 32, base 0xfe800000, size 20, enabled
pcib1: requested memory range 0xfe800000-0xfe8fffff: good
pcib1: matched entry for 1.5.INTA (src \\_SB_.LNKC:0)
pcib1: slot 5 INTA routed to irq 7 via \\_SB_.LNKC
found->	vendor=0x1002, dev=0x960f, revid=0x00
	domain=0, bus=1, slot=5, func=1
	class=04-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0107, statreg=0x4010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=11
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 32, base 0xfe9e8000, size 14, enabled
pcib1: requested memory range 0xfe9e8000-0xfe9ebfff: good
pcib1: matched entry for 1.5.INTB (src \\_SB_.LNKD:0)
pcib1: slot 5 INTB routed to irq 11 via \\_SB_.LNKD
vgapci0: <VGA-compatible display> port 0xc000-0xc0ff mem 0xd0000000-0xdfffffff,0xfe9f0000-0xfe9fffff,0xfe800000-0xfe8fffff irq 7 at device 5.0 on pci1
pci1: <multimedia> at device 5.1 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 10 at device 4.0 on pci0
pcib2:   domain            0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0xd000-0xdfff
pcib2:   memory decode     0xfea00000-0xfeafffff
pcib2:   no prefetched decode
ACPI: Found matching pin for 2.0.INTA at func 0: 10
pci2: <ACPI PCI bus> on pcib2
pci2: domain=0, physical bus=2
found->	vendor=0x1106, dev=0x3119, revid=0x82
	domain=0, bus=2, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	map[10]: type I/O Port, range 32, base 0xd800, size  8, enabled
pcib2: requested I/O range 0xd800-0xd8ff: in range
	map[14]: type Memory, range 64, base 0xfeaffc00, size  8, enabled
pcib2: requested memory range 0xfeaffc00-0xfeaffcff: good
pcib2: matched entry for 2.0.INTA (src \\_SB_.LNKA:0)
pcib2: slot 0 INTA routed to irq 10 via \\_SB_.LNKA
vge0: <VIA Networking Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfeaffc00-0xfeaffcff irq 10 at device 0.0 on pci2
vge0: Reserved 0x100 bytes for rid 0x14 type 3 at 0xfeaffc00
miibus0: <MII bus> on vge0
ip1000phy0: <IC Plus IP1001 10/100/1000 media interface> PHY 22 on miibus0
ip1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
vge0: WARNING: using obsoleted if_watchdog interface
vge0: bpf attached
vge0: Ethernet address: 00:02:2a:e0:42:33
vge0: [MPSAFE]
vge0: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> irq 11 at device 7.0 on pci0
pcib3:   domain            0
pcib3:   secondary bus     3
pcib3:   subordinate bus   3
pcib3:   I/O decode        0xe000-0xefff
pcib3:   memory decode     0xfeb00000-0xfebfffff
pcib3:   prefetched decode 0xfdf00000-0xfdffffff
ACPI: Found matching pin for 3.0.INTA at func 0: 11
pci3: <ACPI PCI bus> on pcib3
pci3: domain=0, physical bus=3
found->	vendor=0x10ec, dev=0x8168, revid=0x02
	domain=0, bus=3, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	MSI-X supports 2 messages in map 0x20
	map[10]: type I/O Port, range 32, base 0xe800, size  8, enabled
pcib3: requested I/O range 0xe800-0xe8ff: in range
	map[18]: type Memory, range 64, base 0xfebff000, size 12, enabled
pcib3: requested memory range 0xfebff000-0xfebfffff: good
	map[20]: type Prefetchable Memory, range 64, base 0xfdff0000, size 16, enabled
pcib3: requested memory range 0xfdff0000-0xfdffffff: good
pcib3: matched entry for 3.0.INTA (src \\_SB_.LNKD:0)
pcib3: slot 0 INTA routed to irq 11 via \\_SB_.LNKD
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8111B/8111C/8111CP PCIe Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfebff000-0xfebfffff,0xfdff0000-0xfdffffff irq 11 at device 0.0 on pci3
re0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0xfebff000
re0: MSI count : 1
re0: Chip rev. 0x3c000000
re0: MAC rev. 0x00400000
miibus1: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: bpf attached
re0: Ethernet address: 00:e0:4d:a1:1e:5f
re0: [MPSAFE]
re0: [FILTER]
atapci0: <ATI IXP700 SATA300 controller> port 0xb000-0xb007,0xa000-0xa003,0x9000-0x9007,0x8000-0x8003,0x7000-0x700f mem 0xfe7ff800-0xfe7ffbff irq 4 at device 17.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x7000
atapci0: Reserved 0x400 bytes for rid 0x24 type 3 at 0xfe7ff800
atapci0: [MPSAFE]
atapci0: [ITHREAD]
atapci0: AHCI Version 01.10 controller with 4 ports detected
ata2: <ATA channel 0> on atapci0
ata2: SATA connect time=0ms
ata2: SIGNATURE: 00000101
ata2: ahci_reset devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: SATA connect status=00000000
ata3: ahci_reset devices=0x0
ata3: [MPSAFE]
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: SATA connect status=00000000
ata4: ahci_reset devices=0x0
ata4: [MPSAFE]
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: SATA connect status=00000000
ata5: ahci_reset devices=0x0
ata5: [MPSAFE]
ata5: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfe7fe000-0xfe7fefff irq 10 at device 18.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fe000
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfe7fd000-0xfe7fdfff irq 10 at device 18.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fd000
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 3 ports with 3 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe7ff000-0xfe7ff0ff irq 10 at device 18.2 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfe7ff000
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
ehci0: Dropped interrupts workaround enabled
usb2: EHCI version 1.0
usb2: companion controllers, 3 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 6 ports with 6 removable, self powered
ohci2: <OHCI (generic) USB controller> mem 0xfe7fc000-0xfe7fcfff irq 7 at device 19.0 on pci0
ohci2: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fc000
ohci2: [GIANT-LOCKED]
ohci2: [ITHREAD]
usb3: OHCI version 1.0, legacy support
usb3: SMM does not respond, resetting
usb3: <OHCI (generic) USB controller> on ohci2
usb3: USB revision 1.0
uhub3: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 3 ports with 3 removable, self powered
ohci3: <OHCI (generic) USB controller> mem 0xfe7fb000-0xfe7fbfff irq 7 at device 19.1 on pci0
ohci3: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7fb000
ohci3: [GIANT-LOCKED]
ohci3: [ITHREAD]
usb4: OHCI version 1.0, legacy support
usb4: SMM does not respond, resetting
usb4: <OHCI (generic) USB controller> on ohci3
usb4: USB revision 1.0
uhub4: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 3 ports with 3 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe7fa800-0xfe7fa8ff irq 11 at device 19.2 on pci0
ehci1: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfe7fa800
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
ehci1: Dropped interrupts workaround enabled
usb5: EHCI version 1.0
usb5: companion controllers, 3 ports each: usb3 usb4
usb5: <EHCI (generic) USB 2.0 controller> on ehci1
usb5: USB revision 2.0
uhub5: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb5
uhub5: 6 ports with 6 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP700 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xff00
ata0: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=7f ostat1=7f
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata0: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata0: reset tp2 stat0=ff stat1=ff devices=0x0
ata0: [MPSAFE]
ata0: [ITHREAD]
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pcib4:   domain            0
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pcib4:   I/O decode        0xf000-0xfff
pcib4:   no prefetched decode
pcib4:   Subtractively decoded bridge.
pci4: <ACPI PCI bus> on pcib4
pci4: domain=0, physical bus=4
ohci4: <OHCI (generic) USB controller> mem 0xfe7f9000-0xfe7f9fff irq 7 at device 20.5 on pci0
ohci4: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe7f9000
ohci4: [GIANT-LOCKED]
ohci4: [ITHREAD]
usb6: OHCI version 1.0, legacy support
usb6: SMM does not respond, resetting
usb6: <OHCI (generic) USB controller> on ohci4
usb6: USB revision 1.0
uhub6: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6
uhub6: 2 ports with 2 removable, self powered
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
psmcpnp1: <PS/2 mouse port> irq 12 on acpi0
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x810
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 0: ioport 0xc00 alloc failed
ex_isa_identify()
ata: ata0 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
ata1 failed to probe at port 0x170 irq 15 on isa0
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0x491 0x491 0x491 0x491
sio0: probe failed test(s): 0 1 2 4 6 7 9
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0x491 0x491 0x491 0x491
sio0: probe failed test(s): 0 1 2 4 6 7 9
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x491 0x491 0x491 0x491
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 214568 -> 100000
procfs registered
Timecounter "TSC" frequency 2100209104 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad4: 953869MB <Hitachi HDT721010SLA360 ST6OA31B> at ata2-master SATA300
ad4: 1953525168 sectors [1938021C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
ad4: Silicon Image check3 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ATA PseudoRAID loaded
Trying to mount root from ufs:/dev/ad4s1a
start_init: trying /sbin/init
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x5a
acpi: bad write to port 0x000 (8), val 0x7
acpi: bad write to port 0x001 (8), val 0x7
acpi: bad write to port 0x000 (8), val 0x30
acpi: bad read from port 0x001 (8)
acpi: bad read from port 0x000 (8)
acpi: bad write to port 0x000 (8), val 0xa5
Linux ELF exec handler installed